SPECIFICATION SPEC.NO.: REV: X1 DATE: PRODUCT NAME: PRODUCT NO.: DCC ISS APPROVED CHECKED PREPARED E NAME
1. SCOPE(规范) This Product Specification covers the mechanical, electrical and environmental performances requirements and test methods for USB Type-C Rcpt. connector series products. 本规范包含此连接器产品特性，测试方式及品质要求，适用于USB Type-C板端系列产品。 2. APPLICABLE DOCUMENTS(适用文件) The following documents form a part of this specification to the extent specified herein. Unless otherwise specified latest edition of the specification applies. In the event of conflict between requirements of this specification and product drawing product drawing shall take precedence. 本规格书是以下列文件指定的规范来制定，除非另有要求，否则要以最新版本的文件为准，当文 件内容与产品图面发生冲突时，则以产品图面为准。 2.1 Commercial standards, specifications and report（产品标准，规范以及报告） 2.1.1. EIA-STANDARD-364: ELECTRICAL CONNECTOR/SOCKET TEST PROCEDURES 3. REQUIREMENTS (规范要求) 3.1 Green product requirement(绿色产品要求) All of green product shall be mated Halogen Free notices and substances forbidden. 所有绿色产品需满足无卤对禁用物质的要求。 3.2 Materials and finish(材料与电镀) 3.2.1 Contact：High performance copper alloy 讯号端子：高性能铜合金 Finish(电镀)：（a）Contact Area:30u’’ Min. Gold plated 接触区域：接触区域镀金至少30u’’ (b) Solder tail:100u’’ Min. Mattin Tin 焊脚区域：镀锡厚度至少100u’’ (c) Underplate:80u’’ Min. Nickel plated all over 底层电镀：整体电镀镍，厚度至少80u’’ 3.2.2 Housing：Thermoplastic UL94V-0 PA9T GP2450, UL94V-0 塑胶本体：PA9T工程塑胶 I/M Housing：LCP E6808, UL94V-0 I/M 塑胶本体：LCP工程塑胶 3.2.3 Shell: Stainless Steel SUS316L 外壳：不锈钢SUS316L Finish(电镀)：50-180u”Ni plated all over 整体电镀镍50-180u” Middle Shell: Stainless Steel，SUS301 隔离片：不锈钢SUS301 Finish(电镀)： (a) Solder tail:80-180u’’ Min. Mattin Tin 焊脚区域：镀锡厚度80-180u’’ (b) Underplate:50u’’ Min. Nickel plated all over 底层电镀：整体电镀镍，厚度至少50u’’ 3.3 Ratings 3.3.1. Voltage(操作电压)：30V AC Max.(最大交流电30V) 3.3.2 Current(操作电流)：5.0Amperes Max. for VBUS and GND (最小通过电流0.5A) VBUS及GND端子最大通过电流为5A (Pin A1 , A4 , A9 , A12 ; Pin B1 , B4 , B9 , B12) 0.9 Amps Max. for all other contact. 其他端子通过最大电流为0.9A 3.3.3 Operating Temperature(操作温度): -25°C ～ +85°C. 3.3.4 Storage Temperature(存放温度): -40°C ～ +85°C. 3.3.5 Storage Humidity(存放湿度):15~70%RH 3.3.6 Test Humidity(测试湿度):40~85%RH 3.4 Performance and Test Description(功能及测试描述) Product is designed to meet electrical, mechanical and environmental performance requirements specified in Paragraph 3.5, All tests are performed at ambient environmental conditions per EIA-STANDARE-364 unless otherwise specified. 产品必须符合段落3.5所列的电子，机械及环境特性要求，除非另有规定，所有测试皆依EIA-364标准环境状态设置。 3.5 Test Requirents and Procedures Summary(测试需求及程序) 序号 Test ltem 测试描述 Examination of Product 产品检测 Requirement 测试要求 Visual inspection dimensional and functional per applicable quality inspection plan. 目视检验，尺寸和功能符合适用的检测标准。 Test Condition 测试条件 Product shall meet requirements of applicable product drawing and specification. 产品须符合产品图面及规范要求。 1 ELECTRICAL(电气特性) 40 mΩ Max. for VBUS,GND and EIA-364-23B Frequency（频率）:1kHz Current（电流）:100mA max Voltage drop(电压降):20mV max Test Sequence in Figure 2 测试方式请参考图二 Low-Signal Level 2 接触电阻 all other contacts. Maximum change of +10 接触阻抗最大为40 mΩ，测试后最大增加10 mΩ阻抗值 Contact Resistance mΩafter environmental stresses. EIA-364-21 Insulation 3 Resistance 绝缘阻抗 100MΩ Minimum 最小100MΩ Apply DC 500 + 10% V between adjacent contacts of mated connectors for 1 minute. 施加直流电500V于端子或接地之间，保持一分钟。 EIA-364-20 4 Dielectric withstanding Voltage 耐电压 Unmated connectors, apply 100 V AC(RMS) No damage 无击穿 between adjacent terminal or ground. 施加交流电100V于端子或接地之间，保持一分钟。 Differential 5 Impedance 差分阻抗 76Ω minimum 94Ω maximum 76Ω最小值 94Ω最大值 EIA-364-108 40 PS（20%-80%）rise time. 40皮秒（20%-80%）上升时间 When the currents are applied to the EIA-364-70，Method 2 contacts, the temperature rise shall not A current of 5.0 A shall be applied collectively to exceed 30°C at any point on the USB VBUS pins (i.e., pins A4,A9, B4, and B9) and Type-C mated plug and receptacle under test, 1.25 A applied to the VCONN pin (i.e., B5 of the 6 Contact Current Rating 接点额定电流 （温升测试） when measured at an ambient temperature of plug connector) with the return path through the 25°C USB Type-C 线端和板端对插之后开始测试，当电流施加到接触点时，温度上升不得超过30°C。 测试环境温度为25°C。 corresponding GND pins (i.e., pins A1, A12, B1, and B12). A minimum current of 0.25 A shall also be applied individually to all the other contacts. 5.0A电流用在VBUS脚位（A4，A9，B4，B9） 1.25A电流用在VCONN脚位，与回路相对应的GND脚位（A1，A12，B1，B12） 0.25A电流单独应用到其他脚位 The measured differential insertion loss of the mated cable assembly must not exceed the limit defined by the following vertices: 测量对插线缆组件的差动插入损耗必须不超过下面定义的限制： (100 MHz, ?0.25 dB),(2.5 GHz,?0.35 dB),(5 GHz, ?0.45 dB)，(10 GHz, ?0.75 dB) and (15 GHz,?1.85 dB). Super Speed pairs only 只量测高速讯号对 EIA-364-101 100 MHz to 15 GHz Normalized，to 85 ohm differential impedance 100 M Hz到15 G Hz的频率，85欧姆差动特性阻抗。 Differential Insertion Loss of 7 Mated Cable Assemblies 差动插入损耗 Differential Return the mated cable assembly must not exceed Loss of Mated the limit defined by the following vertices: 8 Cable Assemblies 差动拔出损耗 不超过下面定义的限制： The measured differential insertion loss of 测量对插线缆组件的差动拔出损耗必须(100 MHz, ?20 dB),(5 GHz,?20dB),(10 GHz, ?13dB) and (15 GHz,?6 dB). The differential crosstalk measures the unwanted coupling between differential pairs. Both near-end crosstalk and far-end crosstalk for mated connector pairs are specified. The recommended limit is defined by the following vertices: 在对接的连接器中，D+/D-对以及超高速对之间的差动近端和远端串音应尽量不要超过限制，该限制请参考一下的定义： (100 MHz，-40 dB） (5 GHz, -40 dB) (7.5 GHz, 12-36 dB) Defined by the following vertices: (100 MHz, -30 dB), (6 GHz, -30 dB), and (10 GHz, -25 dB). EIA-364-90 40 ps (20%-80%) rise time. 40 皮秒(20%-80%)上升时间 9 Differential Near-End and Far-End Crosstalk Between Super Speed Pairs 差动近远端串音测试 10 Scd21 MECHANICAL REQUIREMENT(机械特性) The initial connector insertion force shall be EIA-364-13 At a maximum rate of 12.5mm (0.492\per minute. 测试参照EIA-364-13C进行，以每分钟12.5mm速度，量测插入力 within the range from 5N(0.51 kgf) to 20N (2.04 kgf) 插入力范围 5N(0.51 kgf) 到 20N(2.04 kgf). 1-1000 Cycles insertion force shall be within the range from 8N(0.82 kgf) to 20N(2.04 kgf) 1000-10000 Cycles insertion force shall be EIA-364-13 At a maximum rate of 12.5mm (0.492\per minute. 测试参照EIA-364-13C进行，以每分钟12.5mm速度，量测拔出力 11 Insertion Force 插入力 12 Withdrawal Force 拔出力 within the range from 6N(0.61 kgf) to 20N(2.04 kgf) 1-1000次拔出力范围为8N(0.82 kgf) 到 20N(2.04 kgf) 1000-10000次拔出力范围为6N(0.61 kgf) 到 20N(2.04 kgf)
Type-C 规格书 - 图文
