组装、冲压、喷漆等专业词汇
Assembly line组装线 Layout布置图
Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子
Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查
fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码
barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管
supervisor 课长 ME制造工程师 MT制造生技
cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条
front plate前板 rear plate后板 chassis 基座 bezel panel面板
power button电源按键 reset button重置键
Hi-pot test of SPS高源高压测试 Voltage switch of SPS 电源电压接拉键
sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序
material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车
personnel resource department 人力资源部
production department生产部门 planning department企划部 QC Section品管科
stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂
common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手
hydraulic machine油压机 lathe车床 planer |'plein|刨床 miller铣床 grinder磨床 driller??床
linear cutting线切割 electrical sparkle电火花 welder电焊机
staker=reviting machine铆合机 position职务 president董事长
general manager总经理
special assistant manager特助 factory director厂长 department director部长
deputy manager | =vice manager副理 section supervisor课长
deputy section supervisor =vice section superisor副课长
group leader/supervisor组长 line supervisor线长 assistant manager助理
to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect material接料 to reverse material 翻料 wet station沾湿台 Tiana天那水
cleaning cloth抹布 to load material上料 to unload material卸料
to return material/stock to退料 scraped |'skræpid|报废 scrape ..v.刮;削
deficient purchase来料不良 manufacture procedure制程
deficient manufacturing procedure制程不良
oxidation |' ksi'dein|氧化 scratch刮伤 dents压痕
defective upsiding down抽芽不良 defective to staking铆合不良 embedded lump镶块
feeding is not in place送料不到位 stamping-missing漏冲 production capacity生产力
education and training教育与训练 proposal improvement提案改善 spare parts=buffer备件 forklift叉车
trailer=long vehicle拖板车 compound die合模 die locker锁模器
pressure plate=plate pinch压板 bolt螺栓
name of a department部门名称
administration/general affairs dept总务部
automatic screwdriver电动启子 thickness gauge厚薄规
gauge(or jig)治具 power wire电源线 buzzle蜂鸣器
defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座 pedal踩踏板 stopper阻挡器 flow board流水板
hydraulic handjack油压板车 forklift叉车 pallet栈板 glove(s)手套
glove(s) with exposed fingers割手套thumb大拇指 forefinger食指 midfinger中指 ring finger无名指 little finger小指 band-aid创可贴
iudustrial alcohol工业酒精 alcohol container沾湿台 head of screwdriver起子头 sweeper扫把 mop拖把
vaccum cleaner吸尘器 rag 抹布
garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain链条 jack升降机 production line流水线 chain链条槽
magnetizer加磁器 lamp holder灯架 to mop the floor拖地 to clean the floor扫地 to clean a table擦桌子 air pipe 气管
packaging tool打包机 packaging打包 missing part漏件 wrong part错件
excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小)
cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头
slipped screwhead/shippery screw thread滑手 speckle斑点
mildewed=moldy=mouldy发霉 rust生锈
deformation变形
burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质
painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤
poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包带折皱 painting make-up补漆 discoloration羿色 water spots水渍
polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质
delivery deadline交货期 cost成本
engineering工程 die repair模修
enterprise plan = enterprise expansion projects企划 QC品管
die worker模工
production, to produce生产 equipment设备 to start a press开机
stop/switch off a press关机 classification整理 regulation整顿 cleanness清扫 conservation清洁 culture教养 qualified products, up-to-grade products良品
defective products, not up-to-grade products不良品 waste废料 board看板 feeder送料机
sliding rack滑料架
defective product box不良品箱 die change 换模 to fix a die装模
to take apart a die拆模 to repair a die修模 packing material包材 basket蝴蝶竺 plastic basket胶筐
isolating plate baffle plate; barricade隔板
carton box纸箱
to pull and stretch拉深
to put material in place, to cut material, to input落料
to impose lines压线
to compress, compressing压缩 character die字模 to feed, feeding送料 transportation运输
(be)qualfied, up to grade合格
not up to grade, not qualified不合格 material change, stock change材料变更
feature change 特性变更 evaluation评估
prepare for, make preparations for 准备
parameters参数
rotating speed, revolution转速
manufacture management制造管理 abnormal handling异常处理 production unit生产单位 lots of production生产批量 steel plate钢板 roll material卷料
manufacture procedure制程 operation procedure作业流程 to revise, modify修订
to switch over to, switch---to throw--over switching over切换 engineering, project difficulty 工程瓶颈
stage die工程模 automation自动化
to stake, staking, reviting铆合 add lubricating oil加润滑油 shut die架模
shut height of a die架模高度 analog-mode device类模器 die lifter举模器 argon welding氩焊 vocabulary for stamping 冲压常词汇
stamping, press冲压
punch press, dieing out press冲床 uncoiler & strainghtener整平机 feeder送料机
rack, shelf, stack料架 cylinder油缸 robot机械手 taker取料机
conveyer belt输送带 transmission rack输送架 top stop上死点 bottom stop下死点 one stroke一行程 inch寸动
to continue, cont.连动 to grip(material)吸料
location lump, locating piece, block stop 定位块 reset复位 smoothly顺利 dent压痕 scratch刮伤
deformation变形 filings铁削
to draw holes抽孔 inquiry, search for查寻
to stock, storage, in stock库存 receive领取
approval examine and verify审核 processing, to process加工 delivery, to deliver 交货 to return delivenry to.
to send delinery back
to retrn of goods退货
registration登记
registration card登记卡 to control管制
to put forward and hand in提报 safe stock安全库存
acceptance = receive验收 to notice通知
application form for purchase请购单 consume, consumption消耗 to fill in填写 abrasion磨损
reverse angle = chamfer倒角 character die字模
to collect, to gather收集 failure, trouble故障 statistics统计
demand and supply需求 career card履历卡
to take apart a die卸下模具 to load a die装上模具 to tight a bolt拧紧螺栓 to looser a bolt拧松螺栓
to move away a die plate移走模板 easily damaged parts易损件 standard parts标准件
breaking.(be)broken,(be)cracked 断裂 to lubricate润滑 common vocabulary for die engineering
模具工程常用词汇
die 模具
figure file, chart file图档
cutting die, blanking die冲裁模 progressive die, follow (-on)die 连续模
compound die复合模 punched hole冲孔 panel board镶块
to cutedges=side cut=side scrap切边 to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸 engraving, to engrave刻印 upsiding down edges翻边 to stake铆合
designing, to design设计 design modification设计变化 die block模块
folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销
die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座
upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓
document folder文件夹
file folder资料夹
to put file in order整理资料 spare tools location手工备品仓 first count初盘人
first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料
work in progress product在制品 casing = containerazation装箱
quantity of physical invetory second count 复盘点数量
quantity of customs count 会计师盘,点数量 the first page第一联
filed by accounting department for reference会计部存查
end-user/using unit(department)使用单位
summary of year-end physical inventory bills
年终盘点截止单据汇总表 bill name单据名称
This sheet and physical inventory list will be sent to accounting
department together (Those of NHK will be sent to financial department)
本表请与盘点清册一起送会计部－(NHK厂区送财会部)
Application status records of year-end physical inventory List and
physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号 plate电镀 mold成型
material for engineering mold testing工程试模材料
not included in physical inventory不列入盘点
sample样品
incoming material to be inspected进货待验
description品名
steel/rolled steel钢材 material statistics sheet 物料统计明细表
meeting minutes会议记录 meeting type 会别
distribution department分发单位 location地点 chairman主席
present members出席人员 subject主题 conclusion结论
decision items决议事项
responsible department负责单位 pre-fixed finishing date预定完成日 approved by / checked by / prepared by核准/审核/承办
PCE assembly production schedule sheet
PCE组装厂生产排配表 model机锺 work order工令 revision版次 remark备注
production control confirmation生产确认
checked by初审 approved by核准 department部门
stock age analysis sheet 库存货龄分析表
on-hand inventory现有库存 available material良品可使用 obsolete material良品已呆滞 to be inspected or reworked 待验或重工 total合计
cause description原因说明 part number/ P/N 料号 type形态
item/group/class类别 quality品质 prepared by制表 notes说明
year-end physical inventory difference analysis sheet
年终盘点差异分析表
physical inventory盘点数量 physical count quantity帐面数量 difference quantity差异量 cause analysis原因分析 raw materials原料 materials物料
finished product成品
semi-finished product半成品 packing materials包材
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品
disposed goods处理品 warehouse/hub仓库 on way location在途仓 oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓 skid/pallet栈板 tox machine自铆机 wire EDM线割 EDM放电机 coil stock卷料 sheet stock片料 tolerance工差 score=groove压线 cam block滑块 pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差
pocket for the punch head挂钩槽 slug hole废料孔
feature die公母模 expansion dwg展开图 radius半径
shim(wedge)楔子
torch-flame cut火焰切割 set screw止付螺丝 form block折刀 stop pin定位销
round pierce punch=die button圆冲子shape punch=die insert异形子 stock locater block定位块 under cut=scrap chopper清角 active plate活动板 baffle plate挡块 cover plate盖板 male die公模 female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板 bushing block衬套 insert 入块
club car高尔夫球车 capability能力 parameter参数 factor系数
phosphate皮膜化成 viscosity涂料粘度 alkalidipping脱脂
main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模
demagnetization去磁;消磁
high-speed transmission高速传递 heat dissipation热传 rack上料 degrease脱脂 rinse水洗
alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理 seal封孔 revision版次
part number/P/N料号 good products良品
scraped products报放心品 defective products不良品 finished products成品 disposed products处理品 barcode条码
flow chart流程表单 assembly组装 stamping冲压 molding成型
spare parts=buffer备品 coordinate座标
dismantle the die折模 auxiliary fuction辅助功能 poly-line多义线 heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾
derusting machine除锈机 degate打浇口 dryer烘干机 induction感应
induction light感应光
response=reaction=interaction感应ram连杆
edge finder巡边器 concave凸 convex凹
short射料不足 nick缺口 speck瑕?? shine亮班 splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色
gouge沟槽;凿槽
satin texture段面咬花 witness line证示线 patent专利 grit沙砾
granule=peuet=grain细粒 grit maker抽粒机 cushion缓冲
magnalium镁铝合金 magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨 drill铝 boring镗 blinster气泡 fillet镶;嵌边
through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank摸柄
crank shaft曲柄轴
augular offset角度偏差 velocity速度
production tempo生产进度现状 torque扭矩
spline=the multiple keys花键 quenching淬火 tempering回火 annealing退火 carbonization碳化 alloy合金
tungsten high speed steel钨高速的moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性 resistance电阻 ion离子
titrator滴定仪
模具行业专业术语（英语）
