毛重
定量值
定量值—落差
定量值—设定点1
判断—设定点
过量 不足
零点附近
零点附
比较禁止时间 判断时间
稳定 完成 完成时间
过量
适中 不足
比较禁止时判断时间
完成信号输出时间
The time chart on the previous page used a “ Compare regularly ” which is decided by selecting in “ Over/Under Comparison 2 ” of the Comparison mode. 上图是在常规比较状态下的毛重-时间图，常规比较状态可在比较状态的过量/不足比较2中选定。
The period of the output “ Complete ” signal is decided by selecting in “ Complete signal output ” of the Comparison mode. 完成信号的输出周期段可在比较状态的完成信号输出中设定
◇ The duration of the signals t1, t2 and t3 are inputted in the same Comparison mode. 信号t1、t2和t3的持续时间在相同的比较状态中选定 t1 : Comparison Inhibit Time, during this period do not comparing with the set values, it eliminates false in tuning hoper gates (or valves) 比较禁止时间，在此时间段内不对设定值进行比较。用于消除调整料门产生的误差 t2 : Judging Time, it works for the same purpose but during free fall period判断时间，该段时间的作用同上，只是应用的时间段为物料自由下落时间段内。 t3 : Complete Output Time, the complete signal output duration完成输出时间，完成信号输出的时间段 ◇ Conditional formulas : 条件式 When weighing value ≦set value of Near Zero, the Near Zero output signal turns on. 称重值≦零点附近设定值时，零点附近输出信号为ON When weighing value ≧Final －Set Point 1, the SP1 output signal turns on. 称重值≧定量值—设定点1设定值时，SP1输出信号为ON When weighing value ≧Final －Set Point 2, the SP2 output signal turns on. 当称重值≧定量值—设定点2设定值时，SP2输出信号为ON When weighing value ≧Final －CPS, the SP3 output signal turns on. 当称重值≧定量值—落差设定值时，SP3输出信号为ON When weighing value ＜Final －Under, the Under output signal turns on. 当称重值＜定量值—不足时，不足输出信号为ON When weighing value ＞Final ＋Over, the Over output signal turns on. 当称重值＞定量值+过量，过量输出信号为ON When Final ＋Over ≧weighing value ≧Final －Under, the Go output signal turns on. 当 称重值+过量≧称重值≧定量值—不足，适量输出信号为ON ◇ The compared weighing value at Near Zero can be selected Gross, Net, Absolute Gross, Absolute Net or Comparison OFF in “ Near Zero Comparison ”; 零点附近的比较称重值可以在“零点附近比较”中设定为毛重、净重、绝对毛重、绝对净重或者比较OFF ◇ The compared weighing value with Final, Over/Under can be selected Gross, Net or Comparison OFF in “ Over/Under Comparison 1 ” of the Comparison mode. 设定值和过量/不足的比较称重值可以在比较状态的过量/不足比较1中设定为毛重、净重、和比较OFF。 7-2. Sequence with Judgment 有判断功能的序列控制 净重 定量值 定量值—落定量值—设定点2 定量值—设定点1 零点附近 过量 不足 去皮重 起动 停止 完成 判断 （适中、过量/不足） 比较禁止时判断时间 完成输出时完成禁止时间 判断 完成输出时间 ◇ Sequence mode ignores the selections in “Upper/Lower Comparison 2” and “Over/Under Comparison 2” of the Comparison mode. Over/Under compares when the “Complete” output signal gets ON and weight value is held. Upper/Lower limit compares regularly. 序列控制中忽略比较状态的上限/下限比较2和过量/不足比较2。当完成输出信号为ON并且保持称重值时，过量/不足进行比较。上限/下限进行常规比较。 ◇ The period of the output ‘Complete’ signal is decided by selecting in “Complete signal output” of the Comparison mode. 在比较状态的“完成信号输出”中设定完成信号的输出周期 ◇ The duration of the signals t1, t2 and t3 are inputted in the same Comparison mode. 在相同的比较状态设定信号t1、t2和t3的持续时间 t1: Comparison Inhibit Time, during this period do not comparing with the set values, it eliminates false in tuning hoper gates (or valves) 比较禁止时间。在此时间段内不对设定值进行比较。用于消除调整料门（或阀）产生的误差 t2: Judging Time, it works for the same purpose but during free fall period判断时间。该段时间的作用同上，只是应用的时间段为物料自由下落时间段内。 t3: Complete Output Time, the complete signal output duration 完成输出时间。完成信号输出的持续时间 ◇ Conditional formulas : 条件式 When weighing value ≦set value of Near Zero, the Near Zero output signal turns on. 当称重值≦零点附近设定值时，零点附近输出信号为ON * Weighing sequence start at the ON edge of the start signal (OFF →ON), SP1, SP2 and SP3 turn ON. 称重序列在起动信号为ON（OFF—ON）时起动，SP1、SP2和SP3为ON When weighing value ≧Final －Set Point 1, the SP1 output signal turns off. 当称重值≧定量值设定值—设定点1设定值时，SP1输出信号为off When weighing value ≧Final －Set Point 2, the SP2 output signal turns off. 当称重值≧定量值设定值—设定点2设定值时，SP2输出信号为off When weighing value ≧Final －CPS, the SP3 output signal turns off. 当称重值≧定量值设定值—落差设定值时，SP3输出信号为off When weighing value ＜Final －Under, the Under output signal turns on. 当称重值＜定量值设定值—不足，不足输出信号为ON When weighing value ＞Final ＋Over, the Over output signal turns on. 当称重值＞定量值设定值+过量，过量输出信号为ON When Final ＋Over ≧weighing value ≧Final －Under, the Go output signal turns on. 当定量值设定值+过量≧称重定量值≧定量值设定值—不足，适量输出信号为ON。 ◇The compared weighing value at Near Zero can be selected Gross, Net, Absolute Gross, Absolute Net or Comparison OFF in “ Near Zero Comoarison ”; 零点附近的比较值可以在“零点附近比较”中设定为毛重、净重、绝对毛重、绝对净重或者比较OFF。 ◇The compared weighing value with Final, Over/Under can be selected Gross, Net or Comparison OFF in “ Over/Under Comparison 1 ” of the Comparison mode.定量值、过重/不足的比较称重值可以在比较状态的“过量/不足比较1”中设定为毛重、净重或者比较OFF。 7-3. The Disablement of The START & STOP Key 起动&停止键无效 To start or stop weighing sequence, except inputting signal via Control I/O, also could push and tab on the Message screen. In order to avoiding the miss touching during systems operation, they could be disabled by going through setting menu, change them to invalid.除了通过I/O控制输入信号之外，还可以按下信息界面的和按键实现称重序列的起动或停止。为避免误操作可以通过菜单将其属性设为无效。 操作如下 7-7. Judging Times, AZ Times and Average Count of AFFC 判断次数、
f简明中文手册
