好文档 - 专业文书写作范文服务资料分享网站

模具英语专业术语

天下 分享 时间: 加入收藏 我要投稿 点赞

模具英语专业术语

模具的分类:

冲压模(五金模): stamping die

分离模: cutting die 成形模: forming die

塑胶模: plastics mold

注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold

铸造模: casting die

砂型铸造: sand casting 压铸模: die casting

锻造模: forging die

塑胶模具术语

一、入水:gate

进入位(入水点): gate location 水口形式: gate type 大水口(侧浇口): edge gate 潜水口: sub-gate 薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate 二次水口:

细水口: pin-point gate 水口大小: gate size

转水口: switching runner/gate 唧嘴口径: sprue diameter 直接水口: direct gate

二、流道: runner

热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate

圆形(整圆/半圆)流道: round(full/half) runner 矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner

流道电脑分析(模流分析): mold flow analysis 流道平衡: runner balance

热嘴: hot sprue/tip 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头: connector plug 插座: connector socket 密封/封料: seal

三、运水:water line

喉塞:line plug 喉管:tube

塑胶管:plastic tube

快速接头:jiffy quick connector plug/socket

四、模具零件:mold components

三板模(细水口模):3-plate mold 二板模(大水口模):2-plate mold

热流道模具: hot-runner/manifold mold 叠层模: stacked mold

边钉/导边:leader pin/guide pin 边司/导套:guide pin/guide bushing 直导套:shoulder guide bushing 有托导套:straight guide bushing 中托司: ejector guide bush 中托边: ejector guide pin 回针: return pin 面板: top clamp plate A板: A plate 推板:stripper plate B板: B plate 托板: support plate 方铁: spacer block

加高方铁: higher spacer block 顶针固定板:ejector retainner plate 顶针板:ejector plate 底板: bottom clamp plate 螺丝: screw

杯头螺丝: socket cup head screw 平头螺丝: socket flat head screw 机米螺丝:

外六角头螺丝: bolt

栓打螺丝(等高螺丝):S.H.S.B 管钉:dowel pin 开模槽:ply bar socket

内模管位(模仁互锁):core/cavity inter-lock 顶针: ejector pin

司筒:ejector sleeve 司筒针:sleeve ejector pin

缩呵:movable core,return core, core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter

模胚(架): mold base 上内模:cavity insert 下内模:core insert 行位(滑块): slide 行位扣: 镶件:insert 压座/斜鸡:wedge 耐磨板/油板: wear plate 压条:gib

撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate

定位圈(法兰):locating ring 锁扣(模锁):latch 扣鸡:parting lock set 推杆:push bar 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 型腔(前模仁): cavity 型芯(后模仁): core 镶针:insert pin 销子(销钉):dowel pin 波子弹弓:ball catch 喉塞(堵头): pipe plug 锁模块:lock plate 斜顶杆:angle ejector rod 斜顶针:angle from pin 尼龙拉勾:parting locks 活动臂:lever arm

复位键、提前回杆:early return bar 气阀:valves

斜导边(斜导柱):angle pin 油缸: hydraulic cylinder

液压马达: hydraulic motor 齿轮: gear 轴承: bear 术语:terms

承压平面平衡:parting surface support balance 分模面排气:parting line venting

回针碰料位:return pin and cavity interference 模总高超出啤机规格:mold base shut hight 顶针碰运水:water line interferes with ejector pin 料位出上/下模:part from cavity (core) side

模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件: Do not use (core/cavity) insert 用铍铜做镶件: use beryllium copper insert 初步模图设计:preliminary mold design 正式模图设计: final mold design 反呵:reverse core

弹弓压缩量:spring compressed length 稳定性好:good stability,stable 强度不够:insufficient rigidity 均匀冷却:even cooling 扣模(粘模):sticking 顶白: stress mark 热膨胀:thero expansion 缩水: shrinkage

物料表: BOM 原料: raw materials 物料: materials

工程试模材料: material for engineering mold testing 成品: finished product 半成品: semi-finished product 公差:tolorance

铜公(电极):copper electrode 射料不足: short shot 缺口: nick 瑕疪(斑点): speck 亮斑: shine 银纹: splay 焦痕: gas mark 起鳞: delamination 冷块: cold slug 导色: blush 沟槽;凿槽: gouge 段面咬花: satin texture

证示线: witness line 专利: patent 沙砾: grit

细粒: granule=peuet=grain 抽粒机: grit maker 缓冲: cushion

不锈钢: stainless steel 镁铝合金: magnalium 镁金属: magnesium 钣金: metal plate 车/车床: lathe 铣床/铣床: mill 刨/刨床: plane 磨/磨床: grind 钻/钻床: drill 镗: boring 气泡: blinster 版次: revision 备注: remark

生产确认: production control confirmation 初审: checked by 核准: approved by 部门: department 电镀: plate 成型: molding 样品: sample 雕刻: engrave 蚀纹: texture 加硬: harden

热处理: heat treatment 淬火: quenching 回火: tempering 退火: annealing 碳化: carbonization 铬酸处理: chromate 阳性处理: anodize 氮化: nitrifying

模具英语专业术语

模具英语专业术语模具的分类:冲压模(五金模):stampingdie分离模:cuttingdie成形模:formingdie塑胶模:plasticsmold注射模:injectionmold压缩模:compressionmold铸塑模:transfermold吹塑
推荐度:
点击下载文档文档为doc格式
4jybf40oom667gj1yjqg01k8300wxv01cp3
领取福利

微信扫码领取福利

微信扫码分享