MEMORY存储芯片MAX823TEUK+T中文规格书 - 图文

MAX811/MAX812

4-Pin μP Voltage Monitorswith Manual Reset Input

Pin Description

PIN

MAX811

12

MAX812

1—

NAMEGNDRESET

Ground

Active-Low Reset Output. RESET remains low while VCC is below the reset threshold or while MR is held low. RESET remains low for the Reset Active Timeout Period (tRP) after the reset conditions are terminated.

Active-High Reset Output. RESET remains high while VCC is below the reset threshold or while MR is held low. RESET remains high for Reset Active Timeout Period (tRP) after the reset conditions are terminated.

Manual Reset Input. A logic low on MR asserts reset. Reset remains asserted as long as MR is low and for 180ms after MR returns high. This active-low input has an internal 20k? pull-up resistor. It can be driven from a TTL or CMOS-logic line, or shorted to ground with a switch. Leave open if unused.

+5V, +3.3V, or +3V Supply Voltage

FUNCTION

—2RESET

33MRVCC

44

Detailed Description

Reset Output

A microprocessor’s (μP’s) reset input starts the μP in a known state. These μP supervisory circuits assert reset to prevent code execution errors during power-up, power-down, or brownout conditions.

RESET is guaranteed to be a logic low for VCC > 1V. Once VCC exceeds the reset threshold, an internal timer keeps RESET low for the reset timeout period; after this interval, RESET goes high.

If a brownout condition occurs (VCC dips below the reset threshold), RESET goes low. Any time VCC goes below the reset threshold, the internal timer resets to zero, and RESET goes low. The internal timer starts after VCC returns above the reset threshold, and RESET remains low for the reset timeout period.

The manual reset input (MR) can also initiate a reset. See the Manual Reset Input section.

The MAX812 has an active-high RESET output that is the inverse of the MAX811’s RESET output.

Manual Reset Input

Many μP-based products require manual reset capabil-ity, allowing the operator, a test technician, or external logic circuitry to initiate a reset. A logic low on MR asserts reset. Reset remains asserted while MR is low, and for the Reset Active Timeout Period (tRP) after MR returns high. This input has an internal 20kΩ pull-up resistor, so it can be left open if it is not used. MR can be driven with TTL or CMOS-logic levels, or with open-drain/collector outputs. Connect a normally open momentary switch from MR to GND to create a manual-reset function; external debounce circuitry is not required. If MR is driven from long cables or if the device is used in a noisy environment, connecting a 0.1μF capacitor from MR to ground provides additional noise immunity.

Reset Threshold Accuracy

The MAX811/MAX812 are ideal for systems using a 5V ±5% or 3V ±5% power supply with ICs specified for 5V ±10% or 3V ±10%, respectively. They are designed to meet worst-case specifications over temperature. The reset is guaranteed to assert after the power supply falls out of regulation, but before power drops below the minimum specified operating voltage range for the system ICs. The thresholds are pre-trimmed and exhibit tight dis-tribution, reducing the range over which an undesirable reset may occur.

MAX811/MAX812

4-Pin μP Voltage Monitorswith Manual Reset Input

Absolute Maximum Ratings

Terminal Voltage (with respect to GND) VCC .....................................................................-0.3V to 6.0V All Other Inputs .....................................-0.3V to (VCC + 0.3V)Input Current, VCC, MR ......................................................20mAOutput Current, RESET or RESET ....................................20mAContinuous Power Dissipation (TA = +70°C)

SOT143 (derate 4mW/°C above +70°C) .....................320mW

Operating Temperature Range ...........................-40°C to +85°CJunction Temperature ......................................................+150°CStorage Temperature Range ............................-65°C to +160°CLead Temperature (soldering, 10sec) .............................+300°C

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Electrical Characteristics

(VCC = 5V for L/M versions, VCC = 3.3V for T/S versions, VCC = 3V for R version, TA = -40°C to +85°C, unless otherwise noted.Typical values are at TA = +25°C.) (Note 1)

PARAMETER

Operating Voltage RangeSupply Current

SYMBOLVCCICC

CONDITIONS

TA = 0°C to +70°CTA = -40°C to +85°C

MAX81_L/M, VCC = 5.5V, IOUT = 0MAX81_R/S/T, VCC = 3.6V, IOUT = 0MAX81_LMAX81_M

Reset Threshold

VTH

MAX81_TMAX81_SMAX81_R

Reset Threshold TempcoVCC to Reset Delay (Note 2)Reset Active Timeout PeriodMR Minimum Pulse WidthMR Glitch Immunity (Note 3)MR to Reset Propagation Delay (Note 2)

tMDVIH

MR Input Threshold

VILVIHVIL

MR Pull-Up Resistance

VOH

RESET Output Voltage (MAX812)

VOL

ISOURCE = 150μA, 1.8V < VCC < VTH(MIN)MAX812R/S/T only, ISINK = 1.2mA, VCC = VTH(MAX)

MAX812L/M only, ISINK = 3.2mA, VCC = VTH(MAX)

VCC > VTH(MAX), MAX81_L/MVCC > VTH(MAX), MAX81_R/S/T

2.3

0.8

0.7 x VCC

0.25 x VCC

100.8 x VCC

0.30.4

V

20

30

k?V

tRPtMR

VOD = 125mV, MAX81_L/MVOD = 125mV, MAX81_R/S/TVCC = VTH(MAX)

14010

1000.5

TA = +25°CTA = -40°C to +85°CTA = +25°CTA = -40°C to +85°CTA = +25°CTA = -40°C to +85°CTA = +25°CTA = -40°C to +85°CTA = +25°CTA = -40°C to +85°C

4.544.504.304.253.033.002.882.852.582.55

304020

560

2.632.933.084.38

MIN1.01.2

62.74.63

15104.724.754.464.503.143.152.983.002.682.70

ppm/°CμsmsμsnsμsV

TYP

MAX5.5

UNITSVμA