A Handbook of English for Offshore Oil Drilling 海洋石油钻井常用英语手册 Drilling 钻井
Carry out drilling operation in accordance with the drilling program. 按钻井程序进 行钻井作业.Prepared bell nipple.准备”喇叭口 ”短节.
Make up 2 joints of drill pipe. 接两根钻杆 . Break out this connection.卸开该接头.
Run hole ope ner to sea bee下 扩眼器至 U海底
Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆 . Make up bottom hole assembly 组合下部钻具
Check and reset crow n-saver on every tourS 个班都要检查并重新调整天车防碰 装置.Number stands on trip out and trip in.起下钻时给立柱编号 .
Pick up BHA and run to seafloor. 将下部钻具下至海底 . Pick up sta nds.接立柱
Don' t drill faster than 15 mi nutes for 1 sta n（钻进速度别超过 15 分钟 1 根立柱 Drop TOTCO. 投（陶特测斜仪
Fish TOTCO with overshot. 用打捞筒捞起测斜仪 Resume drilling to T.D. 继续钻进至总深 Circulate 15 mi nutes 循环 15 分钟
Run in hole. 下钻 Put out of hole. 起钻
Make an inventory of all ring gaskets.开一个所有垫圈的清单 Use spinning tong.使用气动扳手 Operate the air win ch.操作气动绞车 Lay down 57 joints of 5
” drillpipe根钻杆
Pick up drill stem test tool. 提起钻杆测试工具 Circulate mud for 2 hours. 循环泥浆 2 小时
Move string during circulation. 在循环时注意活动钻具 Circulate hole clea n.循环清洗井眼 Circulate bottoms up. 循环泥浆几周 Fill up every 5 stands.每 5 柱灌泥浆一次
Check mud weight every 15 minu tes.每 15 分钟检查泥浆比重 Reverse out excess ceme n反循环替出多余的泥浆
Cha nge/replace old mud by new mud用新的泥浆替换出旧的泥浆 Stop drilling. 停止钻进 Drilling ahead. 钻进 Pull out of hole bit. 起出钻头
Change bit.换钻头
Run the wear bushi ng.下抗磨补心
The bit thread type is regular pin.钻头丝扣是正规公扣 What's the mak-uep torque? 上扣扭矩要多大 ? Run in 9 ” colla下.9”钻铤
The cathead can ' t give eno ugh to猫头力量不够 Connect crossover sub接 上配合接头 The tong an gle is too small.大钳的角度太小了 Stop circulating. 停止循环泥浆 Break out the sta nd.卸立柱
Set the si ngle into the mousehole把 这个单根放进鼠洞 Can we break out the pipe with rotary table?可 用转盘卸扣吗 No! Break it out with tong. 不行 ! 要用大钳卸扣 Spin it out with the air spa nner.用气动扳手卸扣 Put the pipe wiper on the stri ng.装上钻杆刮泥器 Don' t set this sta nd bac这根钻杆不要放在钻杆盒上 Make up the lift sub. 接好提升短节 Secure the safety clamp 上紧安全卡瓦
The bit is neari ng the shoe 钻头快到套管鞋了 Slow dow n the running speed放 慢下放速度
This is the un dergauged in terval 这是缩径井段 This is the drilling program. 这是钻井设计书
How much weight on bit is required? 要加多少钻压 ?
Keep the rotary speed at 120---140 RPM转速保持 120---140 转/分保持排量 3000升/分
The pump pressure is too high 泵压太高了 Don' t ream the hole too fas划眼不要太快 Notice the rotary torque.注意转盘扭矩的变化 The pen etrati on rate is gett ing slower 钻速变慢了 The bit is nearly worn out. 钻头快磨光了 Stop drilling at 2000 meters.钻至 2000 米停钻 Circulate for one hour. 循环一个小时 The pump pressure has in crease泵压升高了
One nozzle may be plugged可能有一个水眼（或：喷嘴堵了 What is the hook load?悬重多少？
What' s the pic-kup weight? 上提重量是多少 ?
Keep the flow rate at 3000 LPM. What' s the lowering weight下放重量是多少？ Run in HWDP. 下加重钻杆
A stabilizer is n eeded here这里需要一个扶正器 This is a flexible sub. 这是挠性接头 This is the BHA log. 这是下部钻具组合记录
Record all outside and in side diameters记录好所有（入井工具的内外径eed a short drill collar. 需要一根短钻铤
Pull the cat line. 拉猫头
Operate the break lever 操作（或:扶刹把 Stop the pumps.停泵 Make a wiper trip. 通井
Retrieve wear bushi ng.取出抗磨补心 Bleed off pressure. （释放压 （力 Keep 5 wraps on the drum滚筒上留 5 圈 Set slips.座上卡瓦
If tight hole, repeat wiper trip. 如果井眼紧 , 重复划眼 Setback bottom hole assembly将下部钻具立于钻杆盒内 Make sure all alarms are on确保所有的警报信号都开着 Lay down TDS spinner. 拆下顶部驱动的旋扣器
We n
海洋石油钻井常用英语手册.
