Handset inspection record手机质量检验记录
Lot No.数量： Model型号： Sample Level 抽样水平： Sample Qty: 抽检数量：
Inspection Item 检查项目:
Requirements 技术要求 S-II
AQL质量接受限:
Critical 重缺陷： Minor 小缺陷：
1.0
1.5
Result 结果 a) To check the display and backlight LED voltage between 1.8v and 2.4v PCBA Functional Test 确认显示和背景的发光二极管的电压在1.8v和2.4v之间 PCBA功能测试 b) To adjust the reference clock frequency between 13.824030MHz±10Hz; 调节时钟频率在13.824030MHz±10Hz之间; c) To check measure modulation depth between 325 and 385kHz 确认调制频率在325和385kHz之间 d)To check measure TX power between 21 and 27dBm 确认发射功率在21和27dBm之间 e)To check measure BER between 0 and 40ppm 确认字节错误率在0和40ppm之间 Final Test 成品测试 a) Measure the software version between 612800 and 6FFFFF; 确认软件版本在612800到6FFFF之间。 b) To check keypads response between 40 and 41 确认按键测试反馈值在40 和41 之间。 c) To check display status 确认显示屏的好坏。 d)To measure SLR between 6.25dBm and 7.75dBm 确认发射信号强度在6.25dBm 和 7.75dBm之间。 e)To Measure RLR between 2.25 and 3.75dbm 确认接受信号在2.25 和3.75dbm之间。 f)To write the IPEI number to the Flash between 1000A80000 and 1000AFFFFF 将IPEI 号码写入闪存中， 确保号码在1000A80000 和 1000AFFFFF之间。 OBA Cosmetic Inspection 出货外观检查 a)To check if the maximum gap between screen and plastic parts is <0.5mm 确认屏幕和塑料部件的间隙不得大于0.5mm b)To check the surface of phone, there’s no scratch, dirty, impact etc. 确认手机的表面无划伤，污，碰撞等不良 c) To check the printing number on the keypad should at the center of the keypad and size of printing number should be the same size and clear 检查按键上字母的位置应该在按键的中心位置，而且字母大小应一致和清晰 d) Shall be no readily visible appearance affecting defects on the condition of 30cm(12 inches) distance under Normal Fluorescent light. If a defect is readily visible, see table to determine whether or not or exceeds allowable size limits. 30cm(12inches)自然灯光下，无可见影响外观的缺陷, 如果上述条件下发现一个可见缺陷，可根据外观缺陷尺寸限度表来决定是否可以接受 e) To check the space between front shell and rear shell is according the spec. 检查确认手机上下壳间隙在规格内 f) To check user guide and mount and battery and other accessories are all in package, and label clearness 检查手机包装盒里的说明书,挂钩及其他的附件齐全.标签清晰 Battery 电池 N/A
商检批号:
生产日期: _
判定结果: _____________
认可检验员: ___________
QEI-Aastra office135-7.5-012-F002
QEI-Aastra office135-7.5-012-F002 手机质量检验记录
