ADG604–SPECIFICATIONSSINGLE SUPPLY1ParameterANALOG SWITCHAnalog Signal RangeOn Resistance (RON)On Resistance Match BetweenChannels (?RON)LEAKAGE CURRENTSSource OFF Leakage IS (OFF)Drain OFF Leakage ID (OFF)Channel ON Leakage ID, IS (ON)DIGITAL INPUTSInput High Voltage, VINHInput Low Voltage, VINLInput CurrentIINL or IINHCIN, Digital Input CapacitanceDYNAMIC CHARACTERISTICSTransition TimetON EnabletOFF EnableBreak-Before-Make Time Delay, tBBMCharge InjectionOff IsolationChannel-to-Channel CrosstalkBandwidth –3 dBCS (OFF)CD (OFF)CD, CS (ON)POWER REQUIREMENTSIDDNOTES1
Y Version Temperature Range: –40°C to +125°C.Specifications subject to change without notice.(VDD = 3 V ? 10%, VSS = 0 V, GND = 0 V. All specifications –40?C to +125?C unless otherwise noted.)
25?C–40?C to+85?C–40?C to+125?C0 V to VDD3804204605±0.01±0.1±0.01±0.1±0.01±0.1UnitV?Typ?TypnA TypnA MaxnA TypnA MaxnA TypnA MaxV MinV MaxμA TypμA MaxpF Typns Typns Maxns Typns Maxns Typns Maxns Typns MinpC TypdB TypdB TypMHz TyppF TyppF TyppF TypVIN = VINL or VINHVDD = 2.7 V, VSS = 0 VVS = 1.5 V, IS = –1 mA,Test Circuit 1VS = 1.5 V, IS = –1 mAVDD = 3.3 VVS = 1 V/3 V, VD = 3 V/1 V,Test Circuit 2VS = 1 V/3 V, VD = 3 V/1 V,Test Circuit 2VS = VD = 1 V/3 V,Test Circuit 3Test Conditions/Comments±0.25±0.5±0.5±4±8±102.00.80.00521703202402501001601000.3–657025051718±0.139026520545039022510VS1 = 2 V, VS4 = 0 V, RL = 300 ?,CL = 35 pF, Test Circuit 4RL = 300 ?, CL = 35 pFVS = 2 V, Test Circuit 6RL = 300 ?, CL = 35 pFVS = 2 V, Test Circuit 6RL = 300 ?, CL = 35 pF,VS1 = VS2 = 2 V, Test Circuit 5VS = 0 V to 3.3 V, RS = 0 ?, CL = 1 μF,Test Circuit 7RL = 50 ?, CL = 5 pF, f = 10 MHz,Test Circuit 8RL = 50 ?, CL = 5 pF, f = 10 MHz,Test Circuit 10RL = 50 ?, CL = 5 pF, Test Circuit 9f = 1 MHzf = 1 MHzf = 1 MHzVDD = 3.3 VDigital Inputs = 0 V or 3.3 V0.0011.0μA TypμA Max–4–REV. A
ADG604
TERMINOLOGYVDDVSSGNDIDDISSSDRON?RONRFLAT(ON)IS (OFF)ID (OFF)ID, IS (ON)VD, VSVINLVINHIINL (IINH)CS (OFF)CD (OFF)CD, CS (ON)CINtON (EN)tOFF (EN)tTRANSITIONtBBMCharge InjectionCrosstalkOff IsolationBandwidthInsertion LossMost Positive Power Supply PotentialMost Negative Power Supply in a Dual Supply Application. In single supply applications, this should be tied toground at the device.Ground (0 V) ReferencePositive Supply CurrentNegative Supply CurrentSource Terminal. May be an input or output.Drain Terminal. May be an input or output.Ohmic Resistance between D and SOn Resistance Match between any two channels, i.e., RON Max – RON MinFlatness is defined as the difference between the maximum and minimum value of On resistance as measuredover the specified analog signal range.Source Leakage Current with the Switch “OFF”Drain Leakage Current with the Switch “OFF”Channel Leakage Current with the Switch “ON”Analog Voltage on Terminals D, SMaximum Input Voltage for Logic “0”Minimum Input Voltage for Logic “1”Input Current of the Digital InputChannel Input Capacitance for “OFF” ConditionChannel Output Capacitance for “OFF” Condition“On” Switch CapacitanceDigital Input CapacitanceDelay time between the 50% and 90% points of the digital input and switch “ON” condition.Delay time between the 50% and 90% points of the digital input and switch “OFF” condition.Delay time between the 50% and 90% points of the digital input and switch “ON” condition when switchingfrom one address state to another.“OFF” time or “ON” time measured between the 80% points of both switches, when switching from one addressstate to another.A measure of the glitch impulse transferred from the digital input to the analog output during switching.A measure of unwanted signal that is coupled through from one channel to another as a result of parasitic capacitance.A measure of unwanted signal coupling through an “On” switch.Frequency Response of the “On” SwitchLoss Due to the On Resistance of the Switch–6–REV. A
半导体传感器ADG5433WBRUZ中文规格书 - 图文
