AQL质量接受限:
levelⅡ
Critical/Major 重缺陷/主要缺陷： Minor 轻缺陷：
0.4
TECOM话机质量检验记录
Lot No.数量： Model型号： Sample Level 抽样水平： Sample Qty: 抽检数量：
Inspection Item 检查项目: OBA Cosmetic Inspection 出货外观检查
1
Inspection methods 检验方法 AQL 合格质量 水平 AQL=0.4 Ac＝ Re＝ AQL=1 Ac= Re= Result 结果 Requirements 技术要求 a) To check if the maximum gap between upper shell Visual and back shell is 0.8mm. 确认前后壳部件的间隙不得大于0.8mm. 目测 b) To check if the rubber outside between upper shell and back shell 确认按键rubber不能外露 c) To check if the maximum gap between LED&LCD shell and upper shell is 0.5mm. 确认LED&LCD塑胶部件与前壳部件的间隙不得大于0.5mm. d) To check the surface of phone, there’s no fingerprint. 确认话机的表面无指印。 e) To check the surface of phone, the scratch, dirty, impact etc comply with TECOM cosmetic inspection standard. 确认话机的表面划伤，污，碰撞等不良在TECOM客户标准接受范围之内 f) To check the plaint of LCD shell no miss, no scratch 确认LCD壳上喷层无缺失, 无划伤 g) To check the dirty dot on the LCD lens should smaller than 0.05m2 on the condition of 30cm distance. 20cm 足够强度灯光下，检查LCD 显示区域污点大小应该小于0.05平方毫米。 h) To check the key no sink, no inclusion in phone &key. 确认按键无下陷，机内及按键内无异物 i) To check the function key sequence is correct with WI defined. 检查功能键次序与作业指导书中要求的顺序一致。 j) To check cap on EXPN connector is took away. 检查EXPN接口盖已取下 k) To check hang hook no miss, assembly correctly with WI defined 检查挂壁钩不缺失，与作业指导书中要求的方位一致 l) To check the TXT & Card put on phone correctly with WI requirement 检查话机上的记事本与卡片摆放方式与与作业指导书中要求的方位一致 m) To check there is no accessory(LAN lines*1,Base stand*1,Handset*1, Handset cable*1) miss in phone box 检查附件(附件包含:LAN口网线一根，支架一个，听筒一个，听筒线一根)齐全，不可遗漏 n) To check the accessory put in box according to WI requirement 检查包装盒内的附件按WI要求摆放 o) . To check the surface of handset, the scratch, dirty, impact etc comply with TECOM cosmetic inspection standard. There’s no fingerprint on handset. 检查听筒的表面划伤，污，碰撞等不良在TECOM客户标准接受范围之内. 检查听筒上无指印。 p) To check the base stand assembly correctly, the lock line is in one line. 检查立脚组装到位, lock线对齐 q) To check the carton no damaged, the phone put on carton with WI defined. And the MAC address on carton is same with set in carton. 检查卡通箱无破损，话机按照作业指导书放入卡通箱内。Carton箱上的序列号与话机上的序列号一致。 OBA Functional Test 出货功能测试 a) To test the phone has been reset after testing. Visual/Manual AQL=0.4 检测话机已经恢复出厂设置 b) To test the phone display normally, no crosstalk 检测开机界面正常，完全,无缺失。 c) To test red, green and amber color LED with TECOM provided limit sample. No leak light when LED testing. 检测LED灯红灯亮，绿灯亮，混光灯亮，且符合TECOM混光的下限样品。 d) To test the numeric key, check if the LCD shows the number consists with the key marking. 依次测试数字键,确认LCD显示数字是否与按键标示数字相同。 e) To test all keys on phones, check if the LCD showing is consisting with the key marking. And the key has the feeling when pressing. 依次测试所有键,确认LCD显示是否与按键标示相同.且按键有弹性。 f) Use the reference phone to dial inspect phone to check has the sound from the handset without noise; to check has the sound from headset without noise; to check has the sound from amplifier without noise; to check no sound heard on the reference sample when you press mute key. 用治具话机拨打检验机，检测检验听筒有声音输出且无噪音；检测治具耳机有声音输出且无噪音；当按下静音键，检验机说话时，治具机听不见声音。 g) To test the inspect phone to transfer phone1 to phone2 and hold phone1 to answer phone2. 检测检验机能将1号话机传输到2号话机,实现1号机与2号机通话；保持1号话机的通话，接听2号话机。 h) To test the SW vision is same with WI defined. 检测话机软体版本与作业指导书要求一致。 i) To test the MAC address in phone is same with printing on set label. 检测话机的MAC地址与话机上标签上打印出的一致。 j) To test the PC port running normally by program after connecting LAN and PC connector. 连接LAN和PC连接口，用程序检测PC速运行正常。 目测/手动 Ac＝ Re＝ AQL=1 Ac= Re=
商检批号:__
生产日期: ____
判定结果: _____________
认可检验员: ___________
QEI-TEM-7.5-015-F001TECOM话机质量检验记录
